Skip Navigation

InitialsDiceBearhttps://github.com/dicebear/dicebearhttps://creativecommons.org/publicdomain/zero/1.0/„Initials” (https://github.com/dicebear/dicebear) by „DiceBear”, licensed under „CC0 1.0” (https://creativecommons.org/publicdomain/zero/1.0/)M

muusemuuse

@ muusemuuse @lemm.ee

Posts
4
Comments
172
Joined
1 yr. ago

  • Removed

    What are some obvious or not so obvious silver linings of Trump's disastrous policies? if any

    Jump

  • I’m a US citizen looking for a way out and it’s probably not going to happen because I’m not rich and I’m not important.

    The good news is I will likely be killed over this horseshit soon enough so I won’t have to suffer that long with it.

  • DRM-Free OnlyFans Downloads See Widevine Project Nuked From GitHub

    Jump

  • I2p has a git service

  • shearing on outer walls with PETG in a bambu p1p

    Jump

  • the spool says not to exceed 250

  • shearing on outer walls with PETG in a bambu p1p

    Jump

  • I actually lowered it to 250 and turned off the fan and it didn’t help.

  • cannot get an even first layer with a voron trident

    Jump

  • beacon hovers over the bed. it doesnt touch anything.

  • cannot get an even first layer with a voron trident

    Jump

  • I looked at your guide and theres something interesting mentioned for my model, the trident. the actual temp is lower that the measured temp on the top of the bed due to the thickness of the bed! I shoudl raise it by 10 degrees. I'm going to try that in a bit

  • cannot get an even first layer with a voron trident

    Jump

  • I notice my open air bambu labs p1p doest have any problems like this and it doesnt need a heat soak. Isnt the voron a better machine with higher quality parts?

  • cannot get an even first layer with a voron trident

    Jump

  • its a 25 minute heat soak before each and every print. I wonder if I should break that out of the print start macro and make its own macro.

    its a magnetic sheet so that shouldn't throw anything off. I flipped to the smooth side of the sheet which is much takier but its still having the same issues.

  • cannot get an even first layer with a voron trident

    Jump

  • I am constantly manually tweaking Z offset at the start of prints so here's hoping the heatsoak solves that.

  • cannot get an even first layer with a voron trident

    Jump

  • I have reworked the start_print gcode macro to incorporate a heat soak before scanning for a mesh. While its running that 20 minute soak, I notice that the temperature reading on the beacon coil is actual dropping while everything else is increasing during the soak. Is just above the bed, in the center, doors closed, and its readings are getting steadily lower. What could possibly cause that?

    EDIT: Here's where I ended up with my printer.cfg file for my 300 mm^3 voron trident. Do you see anything suspicious? https://pastebin.com/AxxEypK4

  • cannot get an even first layer with a voron trident

    Jump

  • should I have it remesh each time, save, then load the mesh at the start of each print or should I just have it recall a saved mesh?

  • cannot get an even first layer with a voron trident

    Jump

  • I noticed something while printing. it doesnt have a bed mesh loaded when it prints. it saves the last mesh, but doesnt load it. why?

  • cannot get an even first layer with a voron trident

    Jump

  • cranked up the mesh points and switched from lagrange mesh to bicubic. here we are at 35x25 points. weird, I see spikes.

    Oh and to answer your question, there is one linear rail on the X axis.

  • cannot get an even first layer with a voron trident

    Jump

  • Where could that twist be?

  • Kanye West joins streaming service Twitch — gets banned after seven minutes

    Jump

  • Wait are we turning twitch into club penguin now?

  • Hundreds of smartphone apps are monitoring users through their microphones

    Jump

  • This has been tested and proven time and time again. Google and Apple give apps a method to access the mic that the OS can allow or deny. This is what the apps are supposed to use.

    Facebook doesn’t use that method for passive monitoring, only for active engagement. Don’t looks like it’s working when you go the use the thing and it’s disabled but it’s still listening to you.

    If you must use such a social network, never ever ever use the mobile app. Use the website or don’t use the service at all.

  • Deleted

    Permanently Deleted

    Jump

  • Fuck you. You don’t know what I’m into!

  • Sony Music Among Parties Pushing To Cut Off Internet for Pirating Customers — Supreme Court Asked To Intervene

    Jump

  • Nope

  • Sony Music Among Parties Pushing To Cut Off Internet for Pirating Customers — Supreme Court Asked To Intervene

    Jump

  • I do and I never get emails from my ISP.